Hardcore Sledder banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 27 Results
  1. Arctic Cat General Discussion
    Hey everyone, I am quite new to this. I am working on a couple of sleds right now and I am trying to learn about carburetors. I have done some research and I have not been able to find a complete guide for tuning them. I know bits and pieces of information but I am still missing a lot in...
  2. General Snowmobile Forum
    Hey guys, so I have an 99 Ski doo Mxz 700 and I recently have gone through the carbs and everything as well as tuned it to spec. I started it when it was about 40 degrees out which is quite warm and it ran great. Started it again today as it was 23 out this morning and for some reason it idles...
  3. General Snowmobile Forum
    Hey guys. I brought my 02 ski doo Mxz 800 out today to get it ready for the season and decided to start it just to make sure everything is all good. I went to go start it today and for some reason it sounded like it was running on one cylinder. Pulled both plugs to see what’s going on and the...
  4. Polaris General Discussion
    Hey guys I had a quick question about my chain case cover. I have a 99 xlt 600 and I recently put all new bearings in my chain case while doing a new track. Everything went together smoothly but when I started to put the chain case cover on it just won’t go on.. I have tried everything and no...
  5. Polaris General Discussion
    Recently I picked up a dirt cheap part out sled that came with a brand new studded ripsaw camo plastic track. I wanted to put this track on my 1999 Polaris xlt 600 special as I wanted a little bigger lug. The track is a 1.25 lug I forget the stud length but they are just a hair taller than the...
  6. General Snowmobile Forum
    Hey guys, I currently have a 99 xlt 600 special with a 96 xcr 600 triple triple motor swap project I’ve been working on. I am finally done with everything under the hood now time to work on the suspension and right off the bat I ran into a few issues. One issue I’m having is the driveshaft pto...
  7. General Snowmobile Forum
    For the past year or so I’ve been working on a good size project of motor swapping an xlt with an xcr triple triple motor. The sled is a 1999 xlt special with a 96 xcr 600 triple triple in it. The sled is just about done besides some finishing touches but I was thinking today about the cooling...
  8. IQ chassis
    I’m having a very strange issue with my 600rr. The sled acts like it’s breaking up when accelerating and I can’t give it and anything past 3/4 throttle it doesn’t feel like it’s accelerating anymore. I’ve tried swapping the ignition coil for a known hood one aswell as the cdi. I’ve rebuilt the...
  9. General Snowmobile Forum
    So yesterday I got my project sled all finished a 1998 Polaris xlt special with a 96 Polaris 600 triple triple motor in it. Been a long project and loads of research but when I went to start it for the first time it took many pulls and when it did start to run it ran really boggy and was just...
  10. Indy (AXYS Platform)
    I bought a Polaris Indy 440 Sport (With a touring model seat) as my first sled. Runs and drives great just a couple questions. There is no front light, nor a base for it. How would I get any light installed and working on it. The original light cable is still intact (Picture below)...
  11. General Snowmobile Forum
    Hey guys. I have a 1996 Polaris xcr 600 sp triple triple and am looking for the slide height on the 38mm carbs. The carbs have 400 mains and 40s at the pilot jets. I have looked everywhere and cannot for the life of me find the slide height.
  12. General Snowmobile Forum
    So before I start I should probably mention this sleds history. Not to long ago I traded for a 1996 Polaris xcr 600 sp triple triple. But here is the catch, the motor is a 1996 xcr 600 sp triple triple in a xlt aggressive chassie so someone before me did a motor swap and a very good one at that...
  13. General Snowmobile Forum
    Anyone know the exact model of this engine I have? That I know of it’s a 1997 Polaris xcr 600 triple triple. I have matched the engine model number but in 1996 they also had the same engine number in the SP. Im just a little unsure if it’s a 97 or 96 and also if it’s an sp or not. The sled is an...
  14. XCR MY96-03 and Storm, Ultra Triples
    I own a 1999 Polaris XCR 800 and the carburetor needs to be properly adjusted in all respects. I don't have the baselines for anything except for the idle adjustment screws. The throttle, throttle stop screw, choke, and throttle position sensor aren't adjusted properly and because of that the...
  15. General Snowmobile Forum
    I took the diamond drive out. My machine has engine reverse so there is no reverse gear etc. I am waiting for parts from BD Xtreme and putting a more robust gearing system in there. I do have a shop press.. but does anyone have any schematics etc. also, does anyone have a manual for the 2008...
  16. IQ chassis
    I’m riding a 2007 switchback 600. It’s been a great sled for me but last year I had broke a belt trail riding with a buddy. We got the spare on and all was fine but now the MFD cuts out. It’s fine if I’m going slow or slowly throttle up but if I go over 1/2 throttle it’ll cut out. As soon as I...
  17. Pro-X (2001-2004)
    Hello everyone. I have been trying to adjust my TPS on my 2015 rmk 800 and got stuck. I’ve unhooked the throttle cable, I’ve backed out the set screw and nut On the throttle body. I’ve plugged in my tpstool into the plug leading to the tps sensor. Then I backed out the screws on the tow sensor...
  18. FST/4 stroke
    PLEASE someone help I need to find a scanner tool that will work with my 2006 Polaris fst Someone put me in the direction of something that will work good I also need it by Jan 8th as I am leaving for a trip this weekend so I will pay however much extra on shipping I gotta pay someone please...
  19. Polaris General Discussion
    I recently purchased a 2006 Polaris FST 750 Turbo sled from Kijiji and it was listed as working condition and no issues. When I went to check it out it made no noise and started and ran fine. I did a 4 minute test run and heard nothing just that the Temps were getting a little high. He told me...
1-19 of 27 Results
Top